Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
We have found this article relating to A Step-by-Step Guide to Installing a Bathtub down the page on the internet and thought it made good sense to relate it with you in this article.
Installing a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably hard job. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to vacate the old tub as well as embeded in the new one. Make certain you have certified on your own for the task and also are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to think about using one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your devices and material list ought to consist of the following:
Getting ready for the Setup
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be fairly bothersome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the water and inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill up the bath tub and likewise check the overflow outlet and also the normal outlet for leaks.
Finally, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait until the tub has actually been made use of a minimum of once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The former type should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, bring about complications with dampness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the motion experienced when the tub is in usage. The sealant can crack fairly very early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on Installing A Bathtub, I imagined sharing that excerpt was sensible. Make sure you set aside a second to promote this blog entry if you enjoyed reading it. Thanks a lot for your time. Kindly stop by our blog back soon.
Apply Now
Report this page